Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
twlai  
#1 Posted : Thursday, December 11, 2014 11:13:10 AM(UTC)
twlai

Rank: Member

Groups: Member
Joined: 12/11/2014(UTC)
Posts: 8
Hong Kong

Hi,

My setup is as follows:-

PC > Sound Card > I2S > teleporter (transmitter) > cat 6 > teleporter (receiver) > I2S > DAC

I understand that the clock signal becomes differential after LVDS on teleporter and the jitter through the transmission is low. Is reclocking by Metronome needed in my setup to lower the jitter in clock signal further? I feed the sound card with a XO module of good quality and am not interested in ASRC.

Thank you.

Regards,
Peter
Brian Donegan  
#2 Posted : Thursday, December 11, 2014 4:01:54 PM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
It is certainly not required.

What DAC are you using?
twlai  
#3 Posted : Thursday, December 11, 2014 11:48:29 PM(UTC)
twlai

Rank: Member

Groups: Member
Joined: 12/11/2014(UTC)
Posts: 8
Hong Kong

Thanks, Brian. I use dual wm8741 DACAngel
Russ White  
#4 Posted : Tuesday, December 16, 2014 7:18:26 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
No - definitely not at all needed. :)
twlai  
#5 Posted : Wednesday, January 14, 2015 3:54:39 AM(UTC)
twlai

Rank: Member

Groups: Member
Joined: 12/11/2014(UTC)
Posts: 8
Hong Kong

Thank Russ.

I doubt whether in my setup above, I should put the DAC in master mode whilst the sound card in slave mode to reduce the jitter as follows:-

1. clock (dual output clock) is put next to WM8741 instead of being put next to the I/O of sound card (ICE1724, i.e. envy24ht)
2. 1st output to DAC (Master mode)
3. 2nd output to teleporter (transmitter) > cat 6 > teleporter (receiver) > clock input of I/O of sound card

Would it be a better setup?

Regards,
Peter
Russ White  
#6 Posted : Friday, January 16, 2015 1:58:11 AM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
I tend to prefer putting the master clock as close to the DAC as possible.
twlai  
#7 Posted : Friday, January 16, 2015 3:57:31 AM(UTC)
twlai

Rank: Member

Groups: Member
Joined: 12/11/2014(UTC)
Posts: 8
Hong Kong

Thanks Russ.

Would you please advise how I can connect the clock to one channel of the teleporter transmitter and from the teleporter receiver to the IO device ICE1724?

My suggestion:

Clock
Clock signal > one channel of the teleporter transmitter
Click Gnd > teleporter Gnd

ICE1724
One channel of the teleporter receiver > clock in of ICE1724
Teleporter Gnd > Gnd of the sound card

Is it correct? Further, as the GND of both teleporters are connected, will galvanic isolation be lost?

Regards
Brian Donegan  
#8 Posted : Friday, January 16, 2015 6:04:29 PM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
Ground should be optional, since the Teleporter is sending the clock signal deferentially. I would test w/o it first. There is a jumper on the Teleporter for optionally connecting it's GND to the RJ45 shell.
twlai  
#9 Posted : Friday, January 16, 2015 11:53:31 PM(UTC)
twlai

Rank: Member

Groups: Member
Joined: 12/11/2014(UTC)
Posts: 8
Hong Kong

Thanks Brian.
twlai  
#10 Posted : Saturday, October 15, 2016 6:21:57 AM(UTC)
twlai

Rank: Member

Groups: Member
Joined: 12/11/2014(UTC)
Posts: 8
Hong Kong

Originally Posted by: twlai Go to Quoted Post
Thanks Brian.


My system is down before I put the XO next to my DAC chip, i.e. WM8741. The XO is now put there and 1 clock signal goes to WM8741 direct (master mode) whilst another to sound card's IO chip, i.e. ICE1724 via teleporter (slave mode). The improvement is clearly audible in all aspects. The ground needs not be connected as suggested by Brian.

Highly recommended to use this DAC master CD/CAS slave mode.

N.B. the frequency of both devices must be the same, which is 22.5792 in my case.
Russ White  
#11 Posted : Monday, October 17, 2016 7:37:02 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Glad it is working well!
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (4)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.