Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login
How to connect 4:1 Mux/Demux Digital Switch
Options
View
Go to last post Go to first unread
Previous Topic Next Topic
branko  
#1 Posted : Tuesday, July 29, 2014 9:22:54 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
Hello,

what is the right way to use the (new) 4:1 Mux/Demux Digital Switch and 4-Input Selection Switch (this version has a place for Jumper J1) for Buffalo IIIse?

I have connected 5V and GND to booth boards (on 4-Input Selection Switch to header: pin 2 and 4). Led light up when i turn the switch but there seems not to be a signal changing.
Should header pin 6 (low) go to S0 and pin 8 (high) to S1 on Mux board? have I to use the jumper?

Thx

branko
Back to top

Wanna join the discussion?! Login to your Twisted Pear Audio Support forum accountor Register a new forum account.
Back to top  
branko  
#2 Posted : Thursday, August 21, 2014 5:18:24 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
bump Pray
Back to top
Brian Donegan  
#3 Posted : Thursday, August 21, 2014 10:48:22 PM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
Here's a connection diagram. I am putting this on the MUX web page as well.
Brian Donegan attached the following image(s):
4-1MuxSwitchConnectionDiagram.jpg (206kb) downloaded 62 time(s).

You cannot view/download attachments. Try to login or register.
Back to top
WWW
rkuimelis  
#4 Posted : Sunday, October 26, 2014 1:47:02 AM(UTC)
rkuimelis

Rank: Member

Groups: Member
Joined: 9/22/2010(UTC)
Posts: 12
United States
Referring to Brian's post above, is the product with the layout below (CS8416 4:1) connected in the same way to the updated switch board that contains J1?

Leave J1 open and no special wire jumpers at the switch as with the earlier board revision?

BK

UserPostedImage
Back to top
Brian Donegan  
#5 Posted : Sunday, October 26, 2014 6:27:47 PM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
For the 4:1 Mux Receiver, add the J1 jumper. That was added just for it.
Back to top
WWW
rkuimelis  
#6 Posted : Sunday, October 26, 2014 6:51:27 PM(UTC)
rkuimelis

Rank: Member

Groups: Member
Joined: 9/22/2010(UTC)
Posts: 12
United States
Originally Posted by: Brian Donegan Go to Quoted Post
For the 4:1 Mux Receiver, add the J1 jumper. That was added just for it.


Applause
Back to top
branko  
#7 Posted : Thursday, December 4, 2014 11:53:10 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
Hi,

as I had problems to get my 4:1 mux to working state we tested it today with a friends mux that works fine.
The only visible difference is that his resistor array is mounted the other way them mine.
Is this the problem or could it be the smd chip?

what are the part numbers to look for to replace the buddies?

Branko
Back to top
Rss Feed  Atom Feed
Users browsing this topic
GuestUser
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Youtube
Copyright © Twisted Pear Audio