Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
Hompie Dompie  
#1 Posted : Sunday, August 17, 2008 10:13:46 AM(UTC)
Hompie Dompie

Rank: Member

Groups: Member
Joined: 6/30/2008(UTC)
Posts: 7
Location: Netherlands

This weekend I've finished building the Buffalo + IVY kit. Unfortunately after starting it for the first time one channel didn't work. I could track it down to the right channel of the Buffalo where no signal could be measured. The other channel works fine.

Is there anything I could measure on the Buffalo to find the cause? I hope it's not the ESS9008 that is fried...Pray The voltages I use (& checked) are the recommended 6 and 6.6 volts.

I noticed that the heatsink of the power supply (on the LM317) gets quite hot, almost too hot to touch. This isn't the case with the Ivy's counterpart.

Any hints?

Mark.
Russ White  
#2 Posted : Sunday, August 17, 2008 3:01:08 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Hi Mark,

I am not sure exactly what's wrong.

Can you measure the current draw at VA, and VD on the Buffalo?

Thanks,
Russ
Russ White  
#3 Posted : Sunday, August 17, 2008 3:02:24 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Also check for a short from the right outputs to GND and each of outputs of the on board VREGs(the tab).
Hompie Dompie  
#4 Posted : Monday, August 18, 2008 10:25:44 AM(UTC)
Hompie Dompie

Rank: Member

Groups: Member
Joined: 6/30/2008(UTC)
Posts: 7
Location: Netherlands

Hi Russ, thanks for your help.

VA draws 174 mA, and VD 54 mA.

There's no short between the output & ground, or between ground & the VREG tab (if that's what you meant?)

I've tried another source, in case my rusty old cd-players spdif output was bad, but it didn't make a difference. In both cases the lock-led burns innocently... :-)
I also measured Buffalo's output without IVY connected (maybe it shorted out on the input), but still one channel dead, and the other ok.

Is the ESS9008 very sensitive to static electricity? Think

Russ White  
#5 Posted : Monday, August 18, 2008 11:28:22 AM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Sure it is ESD sensitive, but not any more than most such devices.

VA current draw is a bit high (but not too bad), but VD is fine.

What I meant was to also check for shorts between +out and -out (on right side) to both VREG tabs.

Cheers!
Russ

Edited by user Monday, August 18, 2008 11:30:05 AM(UTC)  | Reason: Not specified

Hompie Dompie  
#6 Posted : Tuesday, August 19, 2008 12:46:48 PM(UTC)
Hompie Dompie

Rank: Member

Groups: Member
Joined: 6/30/2008(UTC)
Posts: 7
Location: Netherlands

Russ White wrote:
Sure it is ESD sensitive, but not any more than most such devices.

It's not that I haven't been careful, but I also didn't use earthed wrist-bands and such. Just trying to find a possible cause.

Russ White wrote:

What I meant was to also check for shorts between +out and -out (on right side) to both VREG tabs.

Cheers!
Russ

Okay, no shorts there either.
I took the board out of the housing and visually checked it, but saw nothing faulty. I'm afraid this Buffalo is dead... Boo hoo! (Or half dead to be precise)

So when was the next batch arriving you said? :)
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.