Atom Feed - Twisted Pear Audio Support - Topic:Volumite doesn't work on dual mono Buffalo II - 20Twisted Pear Audio Support - Atom Feedurn:twistedpearaudio-com:AtomFeed:TwistedPearAudioSupport:Topic:Volumitedoesn'tworkondualmonoBuffaloII-20:1Copyright 2024 Twisted Pear Audio Support2024-03-29T09:14:46Zhttp://www.twistedpearaudio.com/forum/Images/YAFLogo.pngForum Adminhttp://www.twistedpearaudio.comfeedback@twistedpearaudio.comwktk_smilehttp://www.twistedpearaudio.com/forum/profile/4533-wktk-smilewktk_smilehttp://www.twistedpearaudio.com/forum/profile/4533-wktk-smilewktk_smilehttp://www.twistedpearaudio.com/forum/profile/4533-wktk-smileYetAnotherForum.NETurn:twistedpearaudio-com:ftPosts:st1:meid7214:1Volumite doesn't work on dual mono Buffalo II<table class="content postContainer_Alt" width="100%"><tr><td>Solved.<br />I'd forgotten jumper ADDRESS, and my major fault was I was too lazy to wiring between dac-volumite and setting dip switches WHILE DACS ARE RUNNING<img src="/forum/Images/Emoticons/eusa_doh.gif" alt="d'oh!" /> <br /><br />Feeding power to the dacs after correct wiring and dip switch settings, they start running as dual mono mode correctly.<br /><br />I have one IVY III module and one another I/V conversion board, so I had tested dual mono mode using IVY III by simply<br />pararelleling R+/L-, R-/L+ on each Buffalo II. <br /></td></tr></table>2010-10-22T06:50:59-07:002010-10-22T06:50:59-07:00wktk_smile<table class="content postContainer_Alt" width="100%"><tr><td>Solved.<br />I'd forgotten jumper ADDRESS, and my major fault was I was too lazy to wiring between dac-volumite and setting dip switches WHILE DACS ARE RUNNING<img src="/forum/Images/Emoticons/eusa_doh.gif" alt="d'oh!" /> <br /><br />Feeding power to the dacs after correct wiring and dip switch settings, they start running as dual mono mode correctly.<br /><br />I have one IVY III module and one another I/V conversion board, so I had tested dual mono mode using IVY III by simply<br />pararelleling R+/L-, R-/L+ on each Buffalo II. <br /></td></tr></table>urn:twistedpearaudio-com:ftPosts:st1:meid7200:1Volumite doesn't work on dual mono Buffalo II<table class="content postContainer" width="100%"><tr><td>Hi,<br />My Volumite controller chip works only in "stereo mode".<br /><br />Without Volumite, I can sucsessfully select "stereo mode" "(dual)mono mode" with on-board controller.<br /><br />With Volumite, "stereo mode" and volume controling are no probrem, but I cannot enter "mono mode".<br />Volumite controller chip ignores dip switch on/off. <br /><br />* Of course I2C header is connected, PB1 is connected to GND and DAC's on-board controller removed.<br /><br />Any solutions? or my Volumite controller chip itselves have problem?</td></tr></table>2010-10-21T19:17:02-07:002010-10-21T19:17:02-07:00wktk_smile<table class="content postContainer" width="100%"><tr><td>Hi,<br />My Volumite controller chip works only in "stereo mode".<br /><br />Without Volumite, I can sucsessfully select "stereo mode" "(dual)mono mode" with on-board controller.<br /><br />With Volumite, "stereo mode" and volume controling are no probrem, but I cannot enter "mono mode".<br />Volumite controller chip ignores dip switch on/off. <br /><br />* Of course I2C header is connected, PB1 is connected to GND and DAC's on-board controller removed.<br /><br />Any solutions? or my Volumite controller chip itselves have problem?</td></tr></table>